Volatile: Almost Useless for Multi-Threaded Programming

Volatile: Almost Useless for Multi-Threaded Programming

Submitted by Arch D. Robison... on Fri, 11/30/2007 - 12:44

There is a widespread notion that the keyword volatile is good for multi-threaded programming. I've seen interfaces with volatile qualifiers justified as "it might be used for multi-threaded programming". I thought was useful until the last few weeks, when it finally dawned on me (or if you prefer, got through my thick head) that volatile is almost useless for multi-threaded programming. I'll explain here why you should scrub most of it from your multi-threaded code.

Hans Boehm points out that there are only three portable uses for volatile. I'll summarize them here:

• marking a local variable in the scope of a setjmp so that the variable does not rollback after a longjmp.

• memory that is modified by an external agent or appears to be because of a screwy memory mapping

• signal handler mischief

None of these mention multi-threading. Indeed, Boehm's paper points to a 1997 comp.programming.threads discussionwhere two experts said it bluntly:

"Declaring your variables volatile will have no useful effect, and will simply cause your code to run a *lot* slower when you turn on optimisation in your compiler." - Bryan O' Sullivan

"...the use of volatile accomplishes nothing but to prevent the compiler from making useful and desirable optimizations, providing no help whatsoever in making code "thread safe". " - David Butenhof

If you are multi-threading for the sake of speed, slowing down code is definitely not what you want. For multi-threaded programming, there two key issues that volatile is often mistakenly thought to address:

1. atomicity

1. memory consistency, i.e. the order of a thread's operations as seen by another thread.

Let's deal with (1) first. Volatile does not guarantee atomic reads or writes. For example, a volatile read or write of a 129-bit structure is not going to be atomic on most modern hardware. A volatile read or write of a 32-bit int is atomic on most modern hardware, but volatile has nothing to do with it. It would likely be atomic without the volatile. The atomicity is at the whim of the compiler. There's nothing in the C or C++ standards that says it has to be atomic.

Now consider issue (2). Sometimes programmers think of volatile as turning off optimization of volatile accesses. That's largely true in practice. But that's only the volatile accesses, not the non-volatile ones. Consider this fragment:

    volatile int Ready;       


    int Message[100];      


    void foo( int i ) {      


        Message[i/10] = 42;      


        Ready = 1;      


    }

It's trying to do something very reasonable in multi-threaded programming: write a message and then send it to another thread. The other thread will wait until Ready becomes non-zero and then read Message. Try compiling this with "gcc -O2 -S" using gcc 4.0, or icc. Both will do the store to Ready first, so it can be overlapped with the computation of i/10. The reordering is not a compiler bug. It's an aggressive optimizer doing its job.

You might think the solution is to mark all your memory references volatile. That's just plain silly. As the earlier quotes say, it will just slow down your code. Worst yet, it might not fix the problem. Even if the compiler does not reorder the references, the hardware might. In this example, x86 hardware will not reorder it. Neither will an Itanium™ processor, because Itanium compilers insert memory fences for volatile stores. That's a clever Itanium extension. But chips like Power™ will reorder. What you really need for ordering are memory fences, also called memory barriers. A memory fence prevents reordering of memory operations across the fence, or in some cases, prevents reordering in one direction. Paul McKenney's article Memory Ordering in Modern Microprocessors explains them. Sufficient for discussion here is that volatile has nothing to do with memory fences.

So what's the solution for multi-threaded programming? Use a library or language extension hat implements the atomic and fence semantics. When used as intended, the operations in the library will insert the right fences. Some examples:

• POSIX threads

• Windows™ threads

• OpenMP

• TBB

For example, the parallel reduction template in TBB does all the right fences so you don't have to worry about them.

I spent part of this week scrubbing volatile from the TBB task scheduler. We were using volatile for memory fences because version 1.0 targeted only x86 and Itanium. For Itanium, volatile did imply memory fences. And for x86, we were just using one compiler, and catering to it. All atomic operations were in the binary that we compiled. But now with the open source version, we have to pay heed to other compilers and other chips. So I scrubbed out volatile, replacing them with explicit load-with-acquire and store-with-release operations, or in some cases plain loads and stores. Those operations themselves are implemented using volatile, but that's largely for Itanium's sake.  Only one volatile remained, ironically on an unshared local variable! See file src/tbb/task.cpp in the latest download if your curious about the oddball survivor.
- Arch

转载以上文章是为了以后用到时查询方便，及空闲时候再读一遍。



http://software.intel.com/en-us/blogs/2007/11/30/volatile-almost-useless-for-multi-threaded-programming