IMX6ULL UART5配置错误imx6ul-pinfunc.h

最近调试IMX6ULL新项目，配置了UART1_{UART6（arm下映射成ttymxc0}ttymxc5），短接了RX和TX用minicom测试了UART1~ttymxc6，发现UART5只能发，不能收。后来配置成GPIO的方式调试，确认UART5的RX和TX的硬件连接没有问题。最后结合datasheet和imx6ull-pinfunc.h，发现是freescale官方配置管脚寄存器的值有错误。

下面记录一下：

管脚配置：

pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
>;
};
…
&uart5 {
pinctrl-names = “default”;
pinctrl-0 = <&pinctrl_uart5>;
status = “okay”;
};
imx6ull.dtsi 下包含了imx6ull-pinfunc.h 管脚寄存配置头文件

/*

• Copyright 2015-2016 Freescale Semiconductor, Inc.
• This program is free software; you can redistribute it and/or modify
• it under the terms of the GNU General Public License version 2 as
• published by the Free Software Foundation.
  */

#include
#include
#include
#include “imx6ull-pinfunc.h”
#include “imx6ull-pinfunc-snvs.h”
#include “skeleton.dtsi”

/ {
aliases {
can0 = &flexcan1;
can1 = &flexcan2;
ethernet0 = &fec1;
ethernet1 = &fec2;
打开imx6ull-pinfunc.h 发现，里面的内容就只有ENET2，LCD，CSI的一些管脚配置，其他部分跟IMX6UL的管脚配置头文件（imx6ul-pinfunc.h）共用

/*
2 * Copyright © 2016 Freescale Semiconductor, Inc.
3 *
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
7 /
8
9 #ifndef __DTS_IMX6ULL_PINFUNC_H
10 #define __DTS_IMX6ULL_PINFUNC_H
11
12 #include “imx6ul-pinfunc.h”
13 /
14 * The pin function ID is a tuple of
15 *
16 /
17 #define MX6UL_PAD_ENET2_RX_DATA0__EPDC_SDDO08 0x00E4 0x0370 0x0000 0x9 0x0
18 #define MX6UL_PAD_ENET2_RX_DATA1__EPDC_SDDO09 0x00E8 0x0374 0x0000 0x9 0x0
19 #define MX6UL_PAD_ENET2_RX_EN__EPDC_SDDO10 0x00EC 0x0378 0x0000 0x9 0x0
20 #define MX6UL_PAD_ENET2_TX_DATA0__EPDC_SDDO11 0x00F0 0x037C 0x0000 0x9 0x0
21 #define MX6UL_PAD_ENET2_TX_DATA1__EPDC_SDDO12 0x00F4 0x0380 0x0000 0x9 0x0
22 #define MX6UL_PAD_ENET2_TX_EN__EPDC_SDDO13 0x00F8 0x0384 0x0000 0x9 0x0
23 #define MX6UL_PAD_ENET2_TX_CLK__EPDC_SDDO14 0x00FC 0x0388 0x0000 0x9 0x0
24 #define MX6UL_PAD_ENET2_RX_ER__EPDC_SDDO15 0x0100 0x038C 0x0000 0x9 0x0
25 #define MX6UL_PAD_LCD_CLK__EPDC_SDCLK 0x0104 0x0390 0x0000 0x9 0x0
26 #define MX6UL_PAD_LCD_ENABLE__EPDC_SDLE 0x0108 0x0394 0x0000 0x9 0x0
27 #define MX6UL_PAD_LCD_HSYNC__EPDC_SDOE 0x010C 0x0398 0x0000 0x9 0x0
28 #define MX6UL_PAD_LCD_VSYNC__EPDC_SDCE0 0x0110 0x039C 0x0000 0x9 0x0
29 #define MX6UL_PAD_LCD_RESET__EPDC_GDOE 0x0114 0x03A0 0x0000 0x9 0x0
30 #define MX6UL_PAD_LCD_DATA00__EPDC_SDDO00 0x0118 0x03A4 0x0000 0x9 0x0
31 #define MX6UL_PAD_LCD_DATA01__EPDC_SDDO01 0x011C 0x03A8 0x0000 0x9 0x0
32 #define MX6UL_PAD_LCD_DATA02__EPDC_SDDO02 0x0120 0x03AC 0x0000 0x9 0x0
33 #define MX6UL_PAD_LCD_DATA03__EPDC_SDDO03 0x0124 0x03B0 0x0000 0x9 0x0
34 #define MX6UL_PAD_LCD_DATA04__EPDC_SDDO04 0x0128 0x03B4 0x0000 0x9 0x0
35 #define MX6UL_PAD_LCD_DATA05__EPDC_SDDO05 0x012C 0x03B8 0x0000 0x9 0x0
36 #define MX6UL_PAD_LCD_DATA06__EPDC_SDDO06 0x0130 0x03BC 0x0000 0x9 0x0
37 #define MX6UL_PAD_LCD_DATA07__EPDC_SDDO07 0x0134 0x03C0 0x0000 0x9 0x0
38 #define MX6UL_PAD_LCD_DATA14__EPDC_SDSHR 0x0150 0x03DC 0x0000 0x9 0x0
39 #define MX6UL_PAD_LCD_DATA15__EPDC_GDRL 0x0154 0x03E0 0x0000 0x9 0x0
40 #define MX6UL_PAD_LCD_DATA16__EPDC_GDCLK 0x0158 0x03E4 0x0000 0x9 0x0
41 #define MX6UL_PAD_LCD_DATA17__EPDC_GDSP 0x015C 0x03E8 0x0000 0x9 0x0
42 #define MX6UL_PAD_LCD_DATA21__EPDC_SDCE1 0x016C 0x03F8 0x0000 0x9 0x0
43
44 #define MX6UL_PAD_CSI_MCLK__ESAI_TX3_RX2 0x01D4 0x0460 0x0000 0x9 0x0
45 #define MX6UL_PAD_CSI_PIXCLK__ESAI_TX2_RX3 0x01D8 0x0464 0x0000 0x9 0x0
46 #define MX6UL_PAD_CSI_VSYNC__ESAI_TX4_RX1 0x01DC 0x0468 0x0000 0x9 0x0
47 #define MX6UL_PAD_CSI_HSYNC__ESAI_TX1 0x01E0 0x046C 0x0000 0x9 0x0
48 #define MX6UL_PAD_CSI_DATA00__ESAI_TX_HF_CLK 0x01E4 0x0470 0x0000 0x9 0x0
49 #define MX6UL_PAD_CSI_DATA01__ESAI_RX_HF_CLK 0x01E8 0x0474 0x0000 0x9 0x0
50 #define MX6UL_PAD_CSI_DATA02__ESAI_RX_FS 0x01EC 0x0478 0x0000 0x9 0x0
51 #define MX6UL_PAD_CSI_DATA03__ESAI_RX_CLK 0x01F0 0x047C 0x0000 0x9 0x0
52 #define MX6UL_PAD_CSI_DATA04__ESAI_TX_FS 0x01F4 0x0480 0x0000 0x9 0x0
53 #define MX6UL_PAD_CSI_DATA05__ESAI_TX_CLK 0x01F8 0x0484 0x0000 0x9 0x0
54 #define MX6UL_PAD_CSI_DATA06__ESAI_TX5_RX0 0x01FC 0x0488 0x0000 0x9 0x0
55 #define MX6UL_PAD_CSI_DATA07__ESAI_T0 0x0200 0x048C 0x0000 0x9 0x0
56
57 #endif / __DTS_IMX6ULL_PINFUNC_H */
对比datasheet发现，IMX6UL 和IMX6ULL关于UART5_RX的功能选择有些差异：

IMX6UL：（）

#define MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x00C0 0x034C 0x0644 0x0 0x5

IMX6ULL：（）

所以总得来说，解决IMX6ULL UART5无法接受数据的的问题，需要imx6ul-pinfunc.h下的

#define MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x00C0 0x034C 0x0644 0x0 0x5

改为：

#define MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x00C0 0x034C 0x0644 0x0 0x7

问题解决。
————————————————
版权声明：本文为CSDN博主「WXXGoodJob」的原创文章，遵循CC 4.0 BY-SA版权协议，转载请附上原文出处链接及本声明。
原文链接：https://blog.csdn.net/WXXGoodJob/article/details/82690386